Do you use your extractor hood when cooking? The buzzing device is a real asset to the kitchen, especially if you prepare very odorless dishes. It also protects the kitchen surfaces from cooking fat. So double practical!
So that the extractor train runs well for a long time, it must be cleaned regularly. When was the last time with you? A while ago? No problem, because with our tips you get rid of the sticky fat.
Clean the sticky extractor hood
If you have already taken the filter, this is the right time to clean the remaining surfaces of the extractor. Because now you can get to all dirt from both outside and from the inside.
In the case of your cleaning campaign, however, remember not to use any abrasive cleaning agents, rinsing brushes or metal sponges. That can cause scratches.
1.Dishwasher
It is not for nothing that the liquid cleaning agent is part of the basic equipment of every kitchen. It's just totally practical to remove any kind of spots.
- Mix some dishes with warm water. Take a sponge at hand and dive into the mixture.
- Now drive thoroughly across all surfaces.
- Wipes with a wet rag and dries the trigger hood with a soft cloth.
2.baking powder
What is suitable for the fat grille also works well with the rest of the extractor hood. In particular, strong dirt is removed with the home remedy in no time.
- Mix the powder into a paste with a little water. Tails it on the hood.
- After a short exposure time, you wipe them off with a wet rag.
- Then polish the surface with a lint -free cloth.
Tipp: Natron also works wonderfully to clean the extractor.
3.lemon
Citric acid is an environmentally friendly and powerful cleaner. The fat solder also brings extract hoods to shine in no time.
- Cut a lemon open in the middle and rub the cut surface over the dirty areas.
- The juice should have a brief effect. Then swipe it off with warm water.
4.Vegetable oil
This tip sounds counterproductive, but actually works. The oil loosens the crusted fat and brings the surface of your extractor back to shine.
- Put some oil on a piece of kitchen roll.
- Working the oil in the stainless steel in circular movements.
- Wipes with a little household cleaner.
Tipp: Special stainless steel care (such as this fromAmazon*) cleans the metal thoroughly and also maintains it. So it shimmers like new.
Insider tip steam cleaner
A steam cleaner saves you unnecessary scrubbing when cleaning your extractor hood. Due to the hot steam of the device, fat and cooking residues dissolve in no time. As soon as they are liquid, you can wipe them off.
A steam cleaner is particularly useful for the fat filter. But it also gives way to residues on the trigger hood.
- Cover your stove with a few towels or newspaper.
- If necessary, dismantled the fat grille or other parts of the hood to achieve dirty areas.
- Steam the affected areas with your steam cleaner. Fat and Co. should soften quickly.
- Wipes with a damp rag.
Clean the filter of the extractor hood
The filter of your extractor is usually made of metal and is located directly above the stove. He is responsible for freeing the air that is sucked in by the extractor hood when cooking. This prevents the fan from greasing and unusable.
The filter becomes dirty. It is a little annoying to clean. But the right home remedies are doing quite well.
But first:Solve the fat filter from the bracket. You may have to loosen a few small screws. It is best to cover your stove. This prevents your unnecessary dirt.
1. Rash
What is the first remedy you use when you have to rinse greasy pots? Right: detergent. The liquid cleaning agent is also strongly against contamination on your metal filter.
- Put a mixture of warm water and dishwasher cleaners in a large bowl or your sink.
- Immerse yourself in the metal grille and let the solution work for a while.
- With the help of a sponge you can wipe off the dissolved dirt residues. More stubborn remains scrub you with a rinsing brush.
Option: Sets a little fat solder (such as this fromAmazon*) a. So residues have no chance.
2. Baking powder
Baking powder, or alternatively also soda, is not just an environmentally friendly home remedy, it also has! Grandma's darling among the cleaning agents helps you to clean the fat filter of your extractor.
- Put the metal grille in your sink, the bathtub or in a large bucket. Now sprinkle a packet of baking powder over it. Then fill your container with boiling hot water until the filter is covered.
- Let the mixture soak for half an hour. So the dirt slowly loosens.
- With a cloth, remove the other dirt residues under running water. Finally, dry the filter thoroughly - done!
Option: Stir your powder with a little liquid in a small bowl to a paste. Apply it with a cloth on your filter and flush them thoroughly with the dirt after about 10 minutes.
3. dishwasher
Yes, you can also clean your fat filter in the dishwasher if it is big enough. The problem: You have to choose a very intensive program with high temperatures to solve the dirt.
- If your grid is not too dirty, you can put it vertically in the machine and have it rinsed. But it is better not to add additional dishes.
- If your filter is heavily covered with fat, it is best to put it horizontally in the upper drawer of the machine. This means that the water can bounce better and stubborn areas.
Danger:Make sure that your grid can withstand cleaning in the dishwasher. The manufacturer should provide information.
4. oven
You read correctly: You can also clean your metal filter using the oven. In this way, the fat remains are warmed up and can be removed better.
- Place 2-3 layers of baking paper on a baking sheet. Places the metal filter on it and "bake" it for about 30-40 minutes at 110 ° C.
- The fat liquefies and drips onto the baking sheet.
- As soon as the fat has loosened, you can wash the remains.
Why do you have to clean the extractor hood?
Why should you actually clean extractor hoods? After all, they are intended to filter fat and other products from our cooking campaigns. There are several good reasons for this:
- Greasy filters are a fire risk. Fat is inflammatory and should therefore be removed.
- The performance can let go. Bad smells, fat and oil are not sufficiently intercepted. The kitchen smells uncomfortable and there is a fat film on the furniture.
- The engine of the extractor train can become fat. The good piece breaks and has to be replaced. This can cause costs.
- In the fat that accumulates on the filters, bacteria and mold spores feel particularly comfortable. In the warm environment, germs multiply like crazy.
- The extractor hood can quickly look greasy due to the fat splashes and other residues. Cleaning is worthwhile for visual reasons.
How often should you clean the extractor hood?
Unfortunately, there is no general answer to this question. How often you have to clean your extractor hood depends on what and how often you cook.
- If you are a big frying fans and often roast foods, you should clean the hood about once a month.
- If your dishes are a little less fat -heavy, cleaning is enough every three months.
- If you are a cook muffle, you should carry out the cleaning campaign once in six months.
In any case, remember not to delay the cleaning for too long. The longer the fat adheres to the surfaces, the more you have to scrub.
By the way:Some older models have a fat filter fleece. This must be changed every three to six months. This equipment is rather rare these days.
Change activated carbon filters
Depending on the extractor hood, the filters that are used also differ:
- Exhaust air outer hoods guide the smells from the kitchen over a pipe outside. You have a metal filter that is cleaned as described above.
- Clever air exhaust hoods pass the cleaned air back into the room. An activated carbon filter is also used for this.
- Hybrid hoods can lead the exhaust air outside or released them back into the room. This type of trigger hood has both types of filter.
Of course, these filters must also be cleaned and regularly replaced. You should change them after three to six months. That is very simple:
- First remove the grease filter of the hood. This gives you access to the carbon filter. This is captured by brackets that you can easily solve by hand.
- Take out the old filter and install the new one.
Can you also clean activated carbon filters?
Yes, some newer models can be cleaned in the dishwasher or with the heat of the oven. It depends on whether the coal filter is a disposable or reusable system. However, the standard models must be changed regularly.
