Make giant soap bubbles yourself – an exciting DIY project for you and your children

Have you ever been annoyed when you want to make giant soap bubbles yourself and no matter how hard you try, the bubble doesn't want to form properly? Why is this happening? Why do bubbles form at all? In this guide we will share with you the recipe for making giant bubbles yourself and test the limits of how big our bubbles can get. Making homemade large bubbles has probably been on your to-do list for a while, but you've been waiting for the perfect weather conditions. The weather is very important when you make giant soap bubbles yourself that must not burst.

Things worth knowing if you want to make giant soap bubbles yourself

As you may already know, large soap bubbles require more than just surface tension to hold together. Water molecules like to stick together and just like magnets, water molecules bond with each other and form hydrogen bonds, creating surface tension. These allow the water surface to act like an elastic membrane, stretching and holding a shape. If you drop a small amount of water onto a piece of wax paper, you can see a good example of surface tension in action. Instead of splashing or smoothing, the water forms small, spherical droplets on the paper. These water droplets are able to maintain their shape because water molecules are more attracted to each other than to the wax paper. The strength of this attraction helps hold the water droplet together.

If you want to make giant soap bubbles yourself, you only need a few materials, which you can find at your local hardware store. Older children can help tie the string and younger children can measure how much to use. The kids like fun activities like decorating large bubbles with paint, glitter glue, or decorative tape.

Make the best giant soap bubbles yourself

In fact, the surface tension of water is so strong that it prevents us from forming bubbles out of water alone. Adding soap or detergent reduces the surface tension of the water, which can cause bubbles to form. It does this by creating space between water molecules, reducing the strength of their attraction to each other. Think about magnets again - when two magnets are very close together, the pull between them is much stronger than if you slowly separate them. The decrease in attractive force between water molecules reduces the surface tension of the bubble solution, allowing bubbles to form. So this would be agreat DIY weekend projectfor the whole family.

The materials needed

To make your own large bubble wand you will need the following materials:

  • Wooden dowel or wooden rod, approx. 2 cm thick and 12 cm long
  • 2 small screw hooks
  • 1 larger steel washer
  • cotton thread

You can assemble the sticks in just a few minutes. For the solution you need for blowing, you will need a large bucket, a tape measure, scissors and enough space to walk. The bubble solution requires eight cups of water, liquid dish soap, one tablespoon of glycerin and one tablespoon of baking soda.

preparation

DIY

DIY swing for kids - A do-it-yourself project with an old skateboard

By the way, the swing for children that we are going to describe here is not a traditional design that can be seen everywhere. The so-called “Swurfer” allows children to swing while standing. With this extraordinary creation, your little ones will feel like they are surfing a wave.

This activitycould get a little messy. Therefore, from this point on, everything should be outside. First, pour the soap solution into the bucket. If you make your own giant soap bubbles, it's better to make your own soap solution. To do this, combine all the ingredients in the container and stir gently to mix well. Avoid the formation of foam on the water surface. Then screw the screw hooks to one end of each rod, stick or wooden dowel to attach the thread. A little tip at this point would be to wear old clothes in case things get messy. Also, be careful not to blow bubbles near anyone's face.

Now, if you have two dowels with hooks on the end and a short and long string, take the short string and tie each end to the hooks on your dowels. Place a washer on the side for the long cord. You only need one washer, but if you're making giant bubbles yourself, you can use two or even three steel washers. Next, tie the ends of each string to the hooks again. So two separate cords and again you do exactly the same thing, except you already have a washer with you. If you don't want to deal with the screws at the end, you can tie the string directly to the dowels.

The result

Finally, you simply need to dip the wand into the bubble solution. Use this to completely soak the threads and then carefully pull up the wooden stick, keeping the short string taut. Let the long cord hang loosely in a triangle shape. The slower you move, the better results you get.

So if you want to successfully make giant soap bubbles yourself, you and your little ones have to act according to feeling and intuition. Finally, take a step back or hold the cords and gently pull your arms to the side to catch a small breeze. This will take a second or two to get the hang of. Now we hope you have fun with it!